Codan 6760 Manual.pdf

Example of the display: Ending call: 185074 5820 CALL After several seconds, you hear the 5-beep disconnect tone.Sending calls To send a GPS beacon call: Action Notes In Channel mode, select one of the frequencies scanned by the other station.Index controls —D— using 3-17 data sending mode Channel 3-20 display 2-12 brightness 3-28 Clarifier 3-30 contrast 3-29 Free-Tune Receiver 3-33 Multi-Access 6-13 operating types 3-20 —E— Setup 3-20 Single-Access 6-14 emergency RFDS call Sleep 3-17 emergency selcall 4-7, 5-10 View All Settings 3-37 View Channel Options.

Sending calls GPS beacon call GPS (Global Positioning System) is a system for displaying the geographical location of a station.All controls operate the same way in Clarifier mode as they do in Channel mode, except for the Select knob.Using the transceiver Muting the transceiver Muting allows you to silence the transceiver so that you do not hear unwanted background noise on the channel until you receive a call.Sending calls GPS position call GPS (Global Positioning System) is a system for displaying the geographical location of a station.

Advanced features Single-Access mode has a 30 second timeout.You may hear a tuning tone first if the other station has an automatic tuning antenna.Call memory a list containing details of the last ten calls you have received.

For example, excessive signal strength may cause distortion if you transmit to a transceiver sited close to you.If the call repeatedly fails, try another Step 8. channel. Step 1. If No remote GPS was displayed, the call failed because the other station has no GPS receiver connected or no GPS information.The table of contents below only refers to the sections in the guide that describe standard or optional features for your transceiver.The display shows information about the current operation of the transceiver.Enter the address you If the transceiver beeps when want to call (if different you try to enter the address, the to the one displayed) channel has been set up with a.To change channel settings, refer to the HF SSB transceiver reference manual, Chapter 3, Channel creation and editing.

Sending calls Messages like No calls available are displayed if the type of call you are trying to send is not enabled.Sending calls To send a page call: Action Notes To find a good channel See Selective beacon call on to use, send selective page 4-29. beacon calls on the frequencies scanned by the other station.To select a channel by recalling its channel number: Action Notes In Channel mode, press.

To fit a call type, contact Codan for a password that will enable the call type in your transceiver (refer to the HF SSB transceiver reference manual, Chapter 7, Password entry to enable transceiver options).For further details, refer to the 9300 ALE controller user guide (Codan part number 15-04046).Sending calls Action Notes 9. (cont.) While your transceiver waits 20 seconds for call acknowledgment, the display looks like this: Awaiting response 5820 CALL If the call was successful, the display looks like this for three seconds: Page Call succeeded 5820 CALL If the call was unsuccessful, the.All HF SSB series transceivers can send tone and voice calls.Sending calls Emergency selcall with manual channel selection This procedure allows you to select the channel at the time of sending an emergency selcall.About this user guide Standards and icons In this guide, Arial typeface is used for text shown on the transceiver display.Advanced features Using more than one control panel You can control the transceiver from more than one control panel if you have connected one or more control heads to your system.Receiving calls Receiving calls Voice and tone calls are basic calls.To send an RFDS emergency call: Action Notes In Channel mode, select The channel must be set up for a transmit channel emergency RFDS calling.

The red indicator at the top left of the button is on when selcall mute is selected.Page 113: Figure 4.1 Private Network For Sending Telephone Calls.The transceiver automatically transmits GPS information in response to a request from another station.

都市再生機構 - 内閣官房行政改革推進室

When you call a numeric address, your numeric address is used in the call to identify your station (set up in the selcall group assigned to the current channel).

Mobile stations wanting to send telephone calls send telcalls to the base station.Overview The display layout The 4-line display on the control panel tells you what the transceiver is doing.

A control panel left unattended in this mode will not stop other control panels from being used for longer than 30 seconds.Receiving calls Call Message on the display Alarm Notes Alpha ALE Two short ALE call using alpha- FOXTR Called at 20:18 call beeps numeric addresses.Title: codan ngt manual by Taketou Akinori Author: Taketou Akinori Subject: codan ngt manual Keywords: download codan ngt manual pdf, save codan ngt manual pdf, grabb.Sending calls Action Notes 5. (cont.) Within 20 seconds, the other station automatically acknowledges your call by sending a 6-beep tone revertive signal (unless you sent a group call).Sending calls To send a GPS position call: Action Notes To find a good channel See Selective beacon call on to use, send selective page 4-29. beacon calls on the frequencies scanned by the other station.Sending calls Action Notes Wait for the operator of The operator is notified of your the other station to call by an alarm that sounds return your call. like a telephone.

soc.sna/data_erhverv.csv at master · antongrau/soc.sna

In Channel mode, select the best channel and wait until the channel is clear of all voice and.





Links:
Dnapalmhead_no_good_deed_wicked.zip | San Martin Knight of the Andes | C10 1Vf Manual.pdf | Worked examples to eurocode 2 volume 2 |